午夜影院,久久99青青精品免费观看,国产亚洲色婷婷久久99精品,天天日天天色

你好,歡迎訪問濟南金昊化工有限公司!

專注品質,信賴服務

我們用心做產品服務

咨詢熱線:

13655318786

行業新聞

您現在的位置: 網站首頁>>新聞中心>>行業新聞工業上乙二醇的制備方法介紹

工業上乙二醇的制備方法介紹

來源:http://qugjs.com.cn/ 日期:2023-02-02 發布人: 瀏覽次數:0
1、操作前檢查項目
1. Inspection items before operation
平口攪拌車空氣系統運行前檢查潤滑油油位,保持油位在油尺上下線之間,接近下及時提高油位線。,油杯口密封圈完好。
Check the lubricating oil level before the air system of the flat-mouth mixer runs, keep the oil level between the upper and lower lines of the dipstick, and raise the oil level line in time when it is close to the lower limit., The sealing ring of the oil cup port is intact.
2、添加潤滑油的注意事項
2. Precautions for adding lubricating oil
①加油時,應無壓力進行。作業前應將平口攪拌車周圍的灰塵等雜物清理干凈,以免進入注油器。
① Refueling should be carried out without pressure. Before operation, dust and other sundries around the flat-mouth mixer shall be cleaned to avoid entering the oiler.
②注油器內的潤滑油為普通柴油機油,可使用粘度為2.5-7度的潤滑油或工業40#油。儲油杯中的油應及時更換。儲油杯容量以100ml計算,使用100小時為宜。
順酐廠家
② The lubricating oil in the oil injector is ordinary diesel engine oil, and the lubricating oil with viscosity of 2.5-7 degrees or industrial 40 # oil can be used. The oil in the oil cup should be replaced in time. The capacity of the oil storage cup is 100ml, and it is appropriate to use it for 100 hours.
3、維護
3. Maintenance
定期清洗空氣平口攪拌車的濾芯。由于濾芯太臟,進入壓縮機氣缸的空氣中含有過多的灰塵,會加速氣缸和活塞環的磨損,容易形成積碳,影響氣閥的密封性能;會造成拉缸和竄氣,造成潤滑油污染,影響潤滑效果;當氣體被竄氣時,也會出現油污現象。如果氣缸壁與活塞環之間的間隙過大,受污染的潤滑油就會進入壓縮室。并形成油霧,污染壓縮空氣。
Regularly clean the filter element of the air flat mixer. Because the filter element is too dirty, the air entering the compressor cylinder contains too much dust, which will accelerate the wear of the cylinder and piston ring, easily form carbon deposits, and affect the sealing performance of the air valve; It will cause cylinder pulling and blow-by, cause lubricating oil pollution, and affect the lubrication effect; When the gas is blowby, oil contamination will also occur. If the gap between the cylinder wall and the piston ring is too large, the contaminated lubricating oil will enter the compression chamber. And form oil mist to pollute the compressed air.

相關新聞